HUSQVARNA 372 XP®
Power when it's needed!
We cut our own firewood, and living where we do, we have a lot of hardwood trees to cut. Around here, hickory and elm are the two hardest woods to cut. We were using a Jonsered 625ii and wanted a saw that was close in size and power to that saw, and that could run a 24" bar with ease. After looking at a lot of different saws, we chose the 372XP. We haven't used it a ton since we bought it, but we have put it through it's paces. The first thing that we really like is the snap on cover to access the spark plug and air filter. All of our other saws always involved screws to remove the cover. The air filter on this saw is the best that I've ever seen on any saw. It's like an automotive filter! It's easy to screw on and off. We also noticed that it stays pretty clean compared to other saws that we've run. The one complaint that we have about the saw is that it's easy to flood. We've flooded this thing a few times. I suppose that's just a matter of getting used to the saw. This saw is really easy on bar and chain oil. Make sure you read your manual and adjust the oil flow accordingly. Ours came factory one turn out, but we have a 24" bar and the book calls for 3 turns out. It's decent as far as gas consumption. Power is absolutely amazing. This thing screams! The other thing that we noticed is how smooth this thing is compared to our older saws. The anti-vibe on this thing is great. It's actually a bit lighter than the Jonsered 625ii even though this is a bigger saw and has a bigger bar than the Jonsered that we ran. Once this saw is warmed up, it's a breeze to start. You barely pull the cord once and it fires up ready to work. We've never had a warm saw start quite as easy. We don't use the decompression valve, but that's because we've never had one on a saw before and start ours fine without it. It is conveniently located at the top of the saw as opposed to the side of the saw like the older models. The clutch is an inboard clutch which is nice. The chain tensioner is the simplest that I've ever used. It's a really nice saw. It feels like it was designed to be easy to use, operate, and maintain. The owners manual could explain greasing the needle bearing a little better. Other than that, we feel that this saw is a quality saw and wouldn't be afraid to by another one if a tornado blew this one away!
October 7, 2011
Excellent power to weight
Bought this saw as an upgrade from a Stihl 310. I cut lots of firewood almost all oak and madrone, and the home owner saw was struggling a bit. I debated and studied several other pro level saws and settled on the husky 372xp with 24" bar. It was a great decision. The power of a professional saw is truly amazing. I cut almost double the wood in the same time. It flat cuts fast. There are several options for pro saws at this level, I can only speak for the husky, and it is excellent. For a big saw it is as lighter than my 310, and lighter than stihl or dolmar comparable saws. Makes me want to go cut. Excellent!!
March 12, 2015
Recently bought the new Husqvarna 562xp with the autotune. Was really disappointed with it, hard starting even after tuned properly. Seemed to have trouble running right in higher elevation. So I took it back to the local saw shop where I bought it and they were great, gave me my money back towards a brand new 372xp FW powerhead. Couldn't be more happy with this saw, starts first pull cold in the same elevation as before. Runs perfect, really powerful, lots of torque, running a 28 inch bar so it absolutely rips through any wood you throw at it. Mostly Madrone and Oak. I will never give this 372xp up for any other saw. It has proven itself a awesome piece of equipment. Don't change a thing Husky, it's perfect the way it is!
February 22, 2015
This is a great work horse saw. It has the power for a 28" bar in hardwoods. The saw starts well hot or cold. This saw is the perfect weight to power ratio for bucking saw. It is too heavy to use alone but the 550xp and 372xp together make a great combo to handle any job. Its a simple effective design, with an easy to clean air filter. The controls however need major improvement. A saw in this price range should come with an auto return stop switch, and something better than a wimpy piece of plastic to pull on for the choke. Husqvarna needs to redesign the stop switch and choke, and never stop making this great saw!
February 7, 2015
Takes a 50 foot drop no problem
I use the saw daily to fell trees and chuncking down the truck when I climb with it. The saw eats through wood with the 32 inch bar I run on it. The saw is extremely tough. I dropped it about 50 foot up in a tree when clipping it back on my saddle and my lanyard broke causing it to fall. Not the saws fault it was mine. The only thing broke was the chain brake. The groundsmen picked it up and pull it 1 time and it started right up. It does get heavy if you use it for 2 hours in a tree.
January 3, 2015
My first XP saw
I recently purchased this saw as an upgrade from my old, trust 359. I read a lot of reviews on the 372 and knew what I wanted. I cut wood for myself and brother, and we also sell some firewood, so the saw isn't used daily, but weekly mostly. I've been amazed with the saw thus far. The speed, power and feel of the saw are first class in my mind. I've always been a Husqvarna fan, but recently bought a used Stihl MS660 Magnum because it was a good deal. I ran the saw and wasn't impressed with the 20cc bigger performance. Long story short, and a tune up and rings later-although the 660 is in a different class compared to the 372, I'm selling the Stihl. I love this 372. I'm running a 20" bar on it with a Oregon LGX chain and I'll be buying a 24" or 28" for occasional big trees. If you're upgrading from a smaller CC saw, you won't be disappointed. If you're downgrading from a larger CC saw, this one still screams. Check out a YouTube video I linked to see me running the 660 and 372 with 7 pin and 8 pin sprockets.
December 7, 2014
My father bought this saw 14 years ago and hasn't had a single problem with it. He used it and a John Deere to clear the 4 acre lot of bull pines and huge red/white oaks our house is in now. We heat with firewood and have a saw mill so it is used a lot. It starts on the 4th or 5th pull even today. Its nothing compared to my STIHL.
November 16, 2014
Disappointed this time in a Husky saw
I own several Husky's and like them. So I figured I couldn't go wrong buying a new 372XP. I bought one from a local dealer over an hour away from my home. Driving down to pick it up the dealer called me to tell me the saw wouldn't start. He said they should have it fixed by the time I arrived. It wasn't running when I did get there. They were calling around other shops about another carb for it. That is not a way to impress me. I ended up going out to lunch waiting for them to fix it. They said there was some sealant in the jets. Apparently they have had this problem in the 372's. I did take the saw home to try out. I was disappointed to see after spending this kind of money there isn't even a fuel sight gauge on this saw. That shouldn't cost that much. Also why can't I get a scrench that will take off the back bar nut on this thing with a full wrap handle? Husky did put a good air filter on this unit. The saw is decently balanced with a 28" bar on it. The power is there also.
November 7, 2014