Images Working with chainsaws, part 2

Felling method for small trees
Option: Safe corner method
Felling method for large trees

Chainsaw Academy

21/6/2022

Felling against the lean

Felling method for small trees

3 steps

01.

Make a directional notch as normal. Now saw a felling cut that is 2/3 of the truck’s diameter from the rear side of the tree.

Illustration Use Wwc part 2

02.

Insert the wedge or breaking bar straight back in the felling cut.

Illustration Use Wwc part 2

03.

Now complete the felling cut with an oblique cut from the other direction, ensuring the nose of the guide bar slightly overlaps the first cut. You are then at no risk of cutting into the wedge or breaking bar.

Illustration Use Wwc part 2

Option: Safe corner method

4 steps

01.

Make a directional notch as normal. Now make a bore through the trunk and extend the felling hinge laterally.

Illustrations Use Chainsaw Book 1 Working with chainsaws, part 1

02.

Continue to saw backwards to about 2/3 of the trunk’s diameter. Pull back the guide bar to create a 5–10 cm wide corner. Now continue sawing until you cut through the tree. All that then remains is a corner of unsawn timber. The corner is roughly the same total area as the hinge.

Illustrations Use Chainsaw Book 1 Working with chainsaws, part 1

03.

Insert the wedge or breaking bar straight to the back.

Illustration Use Wwc part 2

04.

Finally, saw off the corner and the tree will fall. Place the cut immediately under the previous cut in order to avoid sawing in the felling wedge.

Felling method for large trees

This method can be used if the lean is moderate and the tree is medium-thick to thick.

Video

6 steps

01.

Make a directional notch as normal. Now make a bore to about 60 % ,or slightly more than half, of the tree diameter.

02.

Cut straight backwards through the whole tree.

Illustrations Use Chainsaw Book 1 Working with chainsaws, part 1

03.

Change your position to the other side of the tree. Make a bore that meets the opposite bore and cut straight backwards until you have shaped a suitable corner.

04.

Knock the first wedge in straight back. Start with a wide wedge.

Illustration Use Wwc part 2

05.

Saw off the safe corner.

Images Working with chainsaws, part 2

06.

If necessary, knock in more wedges to make the tree fall. Start with a thicker wedge alongside the first. You can now knock in a third wedge on top of the first.

Images Working with chainsaws, part 2

Previous

Felling across the lean

Next

Felling around the other trees, less than 20 cm in diameter

Last edited: 11/11/2025

Published: 21/6/2022

Part 1Basic tree felling

Working with chainsaws

Chainsaw safety basics

Working with a chainsaw involves many different work situations with both simple and more complicated steps. The chainsaw is a very effective tool, but it can also be dangerous if used improperly. In order to avoid accidents and unnecessary strain, you should use the correct working techniques, the best possible safety equipment and a modern chainsaw with functioning safety features.

Filing the chain

The chainsaw and guide bar should be fixed in a position that ensures stability, and in a way that makes it possible for you to have both hands free for filing. The easiest way is to use a vice on a workbench to secure the guide bar. Make sure the chain is properly tensioned – preferably harder than while cutting – so that it doesn’t move around. For extra stability, you can always activate the chain break.

Planning and felling

How to prepare for felling a tree

It is important that you plan tree felling very carefully. Trees must be felled safely and in the direction that you want them to fall. Well-planned felling also makes it easier to continue with your planned work. The factor that first and foremost affects tree felling is whether there are major obstacles in the area (overhead lines, roads and buildings, etc.). Deploy warning signs if you know that the forestry area is crossed by a road or that a lot of people pass through the area every day.

How to use tree felling tools

The size of the tree determines which felling tools you need to use. For the smallest trees, you do not normally need the felling tools. Hand force is enough, possibly with a long pole. The felling wedge provides greater felling force than the different types of breaking bar. In extreme cases, you can use a rope and winch, which is the safest and most powerful way to fell a tree.

How to remove a hang-up tree

If you accidentally fell a tree into another – always start by taking a break and thinking through the situation calmly. Removing a trapped tree is always a hazardous undertaking and there is no need to rush. Choose the safest solution to the problem even if it takes longer. There are several options. Do not be afraid to call for help – your safety is more important than anything else.

Limbing and crosscutting

How to crosscut a tree

Cutting up a tree trunk into desired lengths can be complicated. For example, the trunk might be very thick; be on a slope; or is lying directly on the ground. Before you begin, carefully consider the condition of the trunk, the stresses that are affecting it, and how the log end will move when you cut through it. Plan the crosscutting procedure carefully, especially for larger logs. An incorrect work technique can be dangerous and cause the trunk to split or the guide bar to become pinched.

Trunks located on a sharp slope

Trees standing on a slope should preferably be felled up the slope so that work can proceed as safely as possible. When working a trunk that is lying on a sharp slope, always stand at the top side of the trunk. Never stand where there is a risk that logs or the whole trunk roll or slide towards you. To support the trunk, keep the hinge intact if there is one, and keep locking branches in place when working.

Part 2Advanced tree felling

Tools

Felling wedges

In many ways, felling wedges are the humble heroes in advanced felling situations, providing remarkable lifting force for greater control and precision. As you know from your basic training, wedges are inserted before the felling cut is complete, and are knocked in with an axe or an impact breaking bar. They help the tree fall in the direction of the notch cut by lifting the tree in that direction. Wedges also prevent the tree from pinching the saw, or leaning back on the saw, while making a back cut. In addition, wedges can be used to release a pinched saw.

Planning

Work Plan

Safety is built on knowledge. Once you have inspected the worksite and the tree, and assessed the risks, it’s time to develop the work plan. But remember that identifying and mitigating risks is a continuous effort at every stage in your planning. For example, be aware that the work methods you decide on as part of your work plan, also have risks that you need to deal with. The same is true for the tools you need to complete the task. Know the risks!

Communicate and Prepare

Be sure to communicate the worksite risk assessment and the work plan to all members of your team. Everybody should understand the risks and the plan for executing the task. It is also now time to prepare yourself, your team and the worksite – taking preventive actions based on the risk assessment. Put on your PPE, block off the worksite, clear your escape routes, position your vehicle so that it is ready for immediate departure in case of urgency, and get out the first aid kit before you start working. Once all team members have signalled a “thumbs up”, the time has come to execute the task.

Execute and Adjust

Now that you have carefully performed and followed each step in the work plan, you and your team are ready to execute the plan. This is where all the time and effort spent with the worksite inspection, the VTA, the worksite risk assessment and deciding on a proper work method really pays off. Making it more likely that you can complete the task safely. But remember: a good plan is not written in stone. More likely than not, you will have to adjust it as you carry out your work.

Essential knowledge for advanced tree felling

Lifting height & Felling force

The lifting height is the distance that the felling tool must push apart the felling cut before the tree falls on its own accord. The diagram shows the required lifting height for different tree diameters, including the saw cut. The values apply to Nordic tree species and trunk forms and should be considered as a guide, not as exact figures. Using the diagram you can, for example, see if you need several wedges in height to bring down the tree.

Leaning trees

Felling across the lean

A tree that leans across the direction of felling wants to fall to the side of your line of sight. You should compensate for the side lean by aiming by the same distance in the opposite direction as the tree is leaning. For example: if the tree leans 1 m to the right, aim at least 1 m to the left. Insert the felling wedge at an oblique angle from the side of the lean allowing the felling force to shore up the tree.

Special trees

Split and crack prone tree species

Splits in the trunks are primarily caused by the internal natural tension in the wood on hard or very hard wood, such as beech. During felling or cutting much of the tension is released. Wood that splits during felling can be a major safety hazard. Split wood can also result in timber losses and, consequently, financial losses. Here are two methods you can use to avoid splitting.

Processing of storm-felled forest