Husqvarna PP 455 E

Det eldrivna hydraulaggregatet Husqvarna PP 455 E har tagits fram speciellt för väggsågen WS 463 och wiresågen CS 2512. PP 455 E är utrustad med vattenkyld elmotor och erbjuder nyutvecklad elektronik som ger säkrare sågning där operatören kan arbeta med full kapacitet under hela sågprocessen. Elmotorn sitter nedanför tanken vilket ger låg tyngdpunkt och bra stabilitet.

Fördelar och användnings- områden
Tekniska specifikationer
Användar- instruktion
Dokumentation
Artikelnr

Fördelar

Monterad på hjul

Den radiostyrda handenheten ger mer information till operatören (effektläge, momentant tryck, drifttid, servicetid, felindikering m.m.), vilket ger full kontroll över sågprocessen och stor rörelsefrihet på arbetsplatsen.
Handenheten har tre olika frekvenslägen för att undvika störning från andra radiostyrda maskiner.
Hydraulsystem med effektiv oljekylare minskar vattenförbrukningen.
Tanken innehåller två av varandra oberoende pump-system: ett för rotation och ett för matning.
För att underlätta förflyttning kan WS 463 enkelt fästas på aggregatet.
Levereras med fjärrkontroll inkl. Canbus-kabel (6 m), 1 laddningsadapter (12 V/230 V). 1 väska för fjärrkontroll med tillbehör, 1 slangsats (8 m).

Väggsågar går att montera fast

För att underlätta förflyttning kan WS 463 enkelt fästas på aggregatet.
Justerbara handtag

Aggregatet går att justera i höjdled och kan läggas bakåt på sina handtag både vid transport och drift.
Anslutningsslangar

Tryckkompenseringen gör det enkelt att ansluta slangarna till kraftaggregatet.
Radiostyrd fjärrkontroll

Den radiostyrda fjärrkontrollen ger betydande information till operatören, som effektnivå, tryck, operatörstid, serviceperioder etc., vilket ger stor rörelsefrihet och total kontroll över sågprocessen.

Tekniska specifikationer för PP 455 E

Motor
Effekt, kW	25 kW
Spänning, V	400 V
Märkström, A	63 A

Hydraulik
Hydrauliskt flöde, max	65 l/min
Hydrauliskt tryck	min: 0 bar; max: 230 bar

Utrustning
Lämplig till	WS 463

Dimensioner
Vikt inkl. olja och slangar	139 kg

Säkerhetsinstruktioner

Safety instructions

Under no circumstances may the machine be started without having read the operators manual and paid special intensions to the safety instructions found in the operators manual. Should the user fail to comply with these, Husqvarna Construction Products Sweden AB or its representatives are free from all liability both directly and indirectly. Read through these operating instructions and make sure that you understand the contents before starting to use the machine. Should you, after reading these safety instructions, still feel uncertain about the safety risks involved you must not use the machine. Please contact your dealer for more information.
Anslut kraftaggregat

Connect power pack 1/2

When the machine has been transported to a suitable site, it should be connected:

Check the hydraulic fluid level in the power unit. This is checked with the level indicator.

Min. level = red line

Max. level = black line

Do not exceed the max. level when filling the tank with hydraulic fluid. The hydraulic fluid expands when it gets hot and can overflow if the level is too high. Tank volume 16 l.

Connect power pack 2/2

Connect the incoming power cable (400 V, 63 A or 400 V, 32 A)

Connect the incoming water hose to the water coupling on the bottom of the motor front on the hydraulic unit.

Connect the remote control using the supplied Canbus cable. Tighten the cable connector screws by hand. When the machine is equipped with a radio, a radio antenna can be connected instead of a Canbus cable. This is screwed into the same socket as where the Canbus cable should have been fitted.
Installera hydraulaggregatet

Fit the hydraulic unit 1/4

Check that the emergency stop switches on the unit and the remote control have not been actuated by turning them in the direction of the arrow.

The display now shows “SELECT FUSE 63A”. If the available fuse is 63 A, confirm this by pressing the membrane key marked “OK”.

If the available fuse is 32 A, press the membrane key marked “up arrow”. In that case the display indicates “SELECT FUSE 32A”. Confirm this by pressing the membrane key marked “OK”.

Fit the hydraulic unit 2/4

Connect the hose assembly. There are two types of hydraulic hoses for the unit:

On a wall saw in the WS 400 series, the four thin hoses control the saw's motion motors, i.e. the saw's blade motion and the saw's trolley motion. The two thick hoses drive the blade.

When a wire saw CS 2512 is connected to the unit, the two thin hoses control the tension on the magazine arm while the two thick hoses drive the wire.

Some couplings on the unit have a red marking sign on the coupling. The hoses with red discs should be connected to these couplings.

Fit the hydraulic unit 3/4

The hydraulic output must be set according to which machine is connected to the hydraulic unit. Select one of the following:

• 25 kW, 230 bar, 65 l/min • 15 kW, 210 bar, 45 l/min or • 9 kW, 140 bar, 40 l/min

Press OK to confirm the selection.

Fit the hydraulic unit 4/4

Connect the water hose between the unit and the saw's water connector and open the water flow valve on top of the unit by turning the hand wheel anticlockwise.

When the power cable and water hoses and hose assembly are connected, the machine can be started. Confirm with “OK”.

The display now shows “Husqvarna PP 455E START MOTOR”. If the display does not show this, follow the instructions shown on the display.
Rengöring

Cleaning

The power pack should be cleaned once work is finished. Use only wet wipes to clean the equipment, do not use washer or high pressure washer to clean the power pack. You should always try to place the power pack away from the wall/wire saw to avoid water splash.
Service

Service

Check regularly:

The hydraulic fluid level in the hydraulic power unit, to make sure it lies between the marks on the level glass.

The tyre pressure.

Any abnormal noises. Note For more information about maintenance, please check the operator’s manual.