Husqvarna PG 680

Husqvarna mudelit PG 680 on suurepärane valik nii suurteks kui väikestes töödeks eriti kommertseesmärgil. Masin on väiksem kui PG 820 ja seetõttu hea manööverdamisvõimega, efektiivne ja lihtne kasutada ilma et peaks tegema järeleandmisi võimsuse ja väljundi osas.

Eelised ja rakendused
Videos
Tehnilised andmed
Soovitatavad tööriistad
Lisatarvikud, osad ja kaasnevad tooted
Kasutusjuhend
Dokumentatsioon

Eelised

Kasutusvaldkond

Kasutusvaldkond
Saab kasutada alates betoonpõrandate ettevalmistamisest ja parandamisest kuni betoonpõrandate lihvimise ja poleerimiseni ning terazzo ja muu looduskivi parandamise ja poleerimiseni.
Suure võimsusega masin

Suure võimsusega masin
Suure võimsusega ja tootlikkusega masin suurendab kasumit ja aitab säästa aega.
Vastupidav masin

Vastupidav masin
Suurepärane tööstuslikuks kasutamiseks mõeldud konstruktsioon tagab atraktiivse kuid vastupidava masina.
Palju erinevaid kasutusvõimalusi

Palju erinevaid kasutusvõimalusi
Võimaldab mitmeid erinevaid rakendusi. Väga mitmekülgne varustus.
Täielikult läbiproovitud

Täielikult läbiproovitud
Igakülgselt läbi proovitud praktilises töös, mis tagab tehnoloogilise efektiivsuse enamus rakenduste j olukordade puhul.
Soodsa hinnaga

Soodsa hinnaga
Kulutused tööriistadele ja hooldusele ruutmeetri/ruutjala kohta on väikesed.
5-kordse tihendusega mehhanism

5-kordse tihendusega mehhanism
Ainulaadne 5-kordne sulgemismehhanism kaitseb laagreid ja sisedetaile betoonitolmu ja püdeliku eest ning pikendab seega masina kasutusiga enne esimest hooldust ja järgmiste hoolduste vahel.
Lihtsalt kasutatav juhtkarp.

Lihtsalt kasutatav juhtkarp.
Juhtkarp on selgelt märgistatud ja hõlpsalt kasutatav. Reguleerib ja juhib masina erinevaid funktsioone.
Redi-Lock™

Redi-Lock™
Husqvarna Redi Lock™ on kiire ja lihtne teemanttööriistade vahetamise süsteem. Tugev konstruktsioon tagab maksimaalse kaitse ja tööea.
Hiperfloor™

Hiperfloor™
Hiperfloor(tm) on unikaalne vähese keskkonnamõjuga meetod betoonpõrandate mehaaniliseks lihvimiseks, töötlemiseks ja poleerimiseks. Lisaks tugevuse ja vastupidavuse tõstmisele muudab see kodude, kommerts- ja tööstuspindade põrandad eriliselt valgustpeegeldavateks.

Dual Drive Technology™ on ainulaadne patenteeritud kahe mootori süsteem, eraldi mootoritega lihvimisketaste ja planetaarpea jaoks.
Kolme peaga lihvijal on uudsed omadused ja kasutusvaldkonnad.
Dual Drive Technology™ planetaar- ja satelliitpeade pöörlemiskiirust ja -suunda saab täielikult üksteisest sõltumatult juhtida.
Väga võimas ja eemaldab kiiresti kõvu vastupidavaid pinnakatteid ning seda või kasutada põrandate poleerimiseks tööstus- ja ärihoonetes.
Madal tööriista ja hoolduskulu ruutmeetri kohta.

Ergonoomilised eelised

Raami ja käepideme disaini tõttu väike mõju kehale.
Dual Drive Technology™

Patenteeritud kahemootoriga seade võimaldab täielikult kontrollida lihvimiskettaid ja planetaarpea liikumiskiirust ja suunda. See suurendab tootlikkuse, lihtsustab masina juhtimist ja laiendab kasutusvaldkonda võrreldes teiste planetaarseadmetega.
Parim oma klassis

Kategooria parim toode nii tootlikkuse, usaldusväärsuse osas ja tootel on teistega võrreldes pikem tööiga esimese ja järgmiste hooldus vahel.
Täiskummirattad.

Täiskummirattad aitavad tagada sujuvama lõikamise ja lihvimise.

Tehnilised andmed: PG 680

Mootor
Võimsus	12,5 kW
Voolutugevus	32 A
Pinge	380 / 480 V
Faasid	3

Spetsifikatsioonid
Lihvimislaius	680 mm

Mõõdud
Kaal	385 kg

Soovitatavad tööriistad

Mudel	G 11X1	G 11X1 D	Redi Lock G 1170	Redi Lock G 1170	Redi Lock G 1140	Redi Lock G 1140	Redi Lock G 1150	Redi Lock G 1150	Redi Lock G 1120	Redi Lock G 1120	Redi Lock G 1180	Redi Lock G 1110	Redi Lock G 1110	Redi Lock G 1110	Redi Lock G 1110	Redi Lock G 1140	Redi Lock G 1110	Redi Lock G 1110
Optimaalne Hea Vastuvõetav —
Materjalid

Safety instructions

Safety instructions

Under no circumstances may the machine be started without having read the operators manual and paid special intensions to the safety instructions found in the operator’s manual. Should the user fail to comply with these, Husqvarna Construction Products Sweden AB or its representatives are free from all liability both directly and indirectly. Read through these operating instructions and make sure that you understand the contents before starting to use the machine. Should you, after reading these safety instructions, still feel uncertain about the safety risks involved you must not use the machine. Please contact your dealer for more information.
Unpacking

Unpacking

To prevent damage to the Grindng shrould when unpacking and transporting ensure to follow the recommended procedure as outline in the supporting video.
Setup workspace

Setup workspace

Position grinder on the working area. Set handle in upright position (illustrated right).

Pull back on handle using the kicker bar to lift grinding head off the ground.

Lay machine back on the ground.

WARNING!

Ensure STOP/RUN switch is in STOP position as unintentional starting of machine while changing discs can result in serious injury.
Assembling diamonds

Assembling diamonds 1/3

Have a set of gloves ready, as diamonds can get very hot during dry grinding applications.

WARNING!

Ensure STOP/RUN switch is in STOP position as unintentional starting of machine while changing discs can result in serious injury.

Assembling diamonds 2/3

As different applications require different selections of diamond tools, there will be many occasions when the grinding discs need to be changed.

Place diamonds as shown in the Redi Lock™ diamond holder disc and secure by tapping lightly. Assembly discs on planetary head lock screws by slightly rotating it.

Note

When using the machine, each grinding head should always have the same diamond type and number of diamonds as the other grinding heads. Each grinding head must have diamonds the same height as the other grinding heads.

WARNING!

Ensure STOP/RUN switch is in STOP position as unintentional starting of machine while changing discs can result in serious injury.

Assembling diamonds 3/3

Once new diamonds have been attached, reverse procedure to lower machine to ground.

Adjust rubber skirt so that a good seal is established between the floor and head of the machine. Ensure join in skirt is at the front of the machine to allow for better air flow. Setting of the skirt is essential to obtain good dust extraction and minimise the possibility of airborne dust.

WARNING!

Ensure STOP/RUN switch is in STOP position as unintentional starting of machine while changing discs can result in serious injury.
Adjusting Handlebar

Adjusting handlebar

Set handle to most comfortable working height using adjustment lever.

Note

It is recommended that this height be set as close as possible to the height of the operator’s hip bone. When the machine is running, there can be a slight grinding force/pull to one side that can be felt through the handlebars. Use the hip to resist this force instead of trying to control this through the arms (such positioning will be much easier for the operator using the machine over prolonged periods of time).
Connect DC

Connect DC

-Connect the hose to the PG Grinder.

-Connect the hose to the DC.

-Attach the plastic bag to the DC, if this is not already in place.

-Plug in the power cable to the DC.

Note

The power cable dipictad in the footage may vary from region to region.
Powering up machine

Powering up machine

Ensure the STOP/RUN switch is set on Stop (rotate counter clockwise).

Plug power supply to machine. Only turn power on at plug once fully connected.

Disengage Emergency Stop button (twist clockwise).

Depress Power button. On doing so, a soft “clunk” should be heard to come from within the electrical cabinet. This indicates the line contactors have engaged, supplying power to the drives/frequency converters.

Note

The power cable dipictad in the footage may vary from region to region.

Note

Always have the DC Vac running before starting to run the Grinder
Smooth start

Smooth start

Standing behind machine with handlebars set as described earlier, apply a small amount of downward pressure on the handle. Switch the machine to run mode using the STOP/RUN switch on the control panel.

The machine should start smoothly and accelerate to the selected speed over a period of 5 seconds.
Setting speed and rotation

Setting Speed and rotation 1/2

On the control panel there is a FORWARD / REVERSE and Speed dial. When starting the machine for the first time on any given application, it is advised that the speed setting should not exceed 7 on start up. As the application allows speeds may be increased during operation.

The machine should start smoothly and accelerate to the selected speed over a period of 5 seconds.

Setting Speed and rotation 2/2

Speed settings should be adapted to the specific application. This will differ from application to application and tools configurations.

For example having a faster satalite speed and slower planetary speed will allow the diamond tools to concertrate in the same area for a longer period of time, giving a higher stock removal rate.

In order to achieve maximum effiency different settings will be required.
Dual drive Technology

Dual Drive Technology™

Two types of planetary effects can be achieved with Dual Drive Technology™ – counter rotation and same direction rotation. Each of them creates a different dynamic under the machine and therefore, a different result in the grinding.
Counter rotation

Counter rotation 1/2

While in counter rotation, the diamonds closer to the centre of the machine move in the direction to the planetary rotation.

The diamonds toward the outside move away from the direction of planetary rotation.

As the inner diamonds are being accelerated in the direction of planatery rotation they grind more aggressively creating an inner band where the machine cuts more effectively.

Counter rotation 2/2

When the machine is moved forward, the middle zone is ground more thoroughtly then the outer zones. The end result is a deeper cut through the middle zone when compared to the outer zones.
Same direction rotation

Same direction rotation 1/2

While in same direction rotation, the diamonds closer to the centre of the machine move in the opposite direction to the planetry rotation.

The diamonds toward the outside move in the direction of planetary rotation.

As the outer diamonds are being accelerated in the direction of planatery rotation they grind more aggressively creating an outer band where the machine cuts more effectively.

Same direction rotation 2/2

When the machine is moved forward, the middle zone is still ground more thoroughtly then the outer zones but not as much as in the case of counter rotation. The end result is a more even cut through the middle zone when compared to the outer zones, which is less prominate then in counter rotation.
Grind-pattern relevancy

Relevance of grindning patterns

All planetary grinders remove more stock from the middle of the grinder. Always overlap the outer zones to ensure efficient and clean grinding.

Remember to change the grinding rotation each pass to maintain a uniformed direction over the floor.
Grinding close to a wall

Grinding close to a wall

When the machine is in operation it will slightly pull to one side. This force is determined by the planetary head rotation. When the head of the machine pulls in to the wall the operator will get a much closer cut to the wall.

A comfortable operating position should allow the handle bar to rest firmly against the operator´s hip.
Diamond selection

Diamond selection

The way diamond segments are set-up on the grinding heads of the machine will also greatly influence the performance of the machine, the productivity levels and also the finished floor quality.
Application reference
Full set vs Half set

Full set vs Half set 1/3

There are basically two types of diamond configurations that can be used when using the Husqvarna PG grinders:

Full set of diamonds. When there are diamonds placed at all positions on the diamond holder discs.

Half set of diamonds. When there are diamonds placed at each alternating positions on the diamond holder discs.

By changing the way the diamonds are set-up on the diamond holder discs, an operator can significantly affect the performance of the machine and therefore the finished product.

Full set vs Half set 2/3

A full set of diamonds will cut a flater floor when compared to a half set of diamonds.

The full set will remove all the high spots instead of carring with the surface of the floor and droping down into the low or softer spots.

With a full set of diamonds the highest level of flatness will be achivied.

Full set vs Half set 3/3

A half set of diamonds will follow the surface of the floor.

The grinder can be placed on an uneven surface and yet still find a stable footing. The half-set diamond configuration should be used when a flat floor is not required.

The half set will carry over the high spots and into the low spots, which is ideal to remove floor coatings or glues where optimum flatness is not the overall objective.
Diamond vs single segment

Diamond vs single segment 1/3

As well as using full set and half set, the operator can also choose from double or single segment tools. This will enable the operator to have control over both his tool economy and productivity.

Double segments: A double segment tool consists of two diamond segments on one Redi Lock™ shoe.

Single segments: A single segment tool consists of one diamond segments on one Redi Lock™ shoe.

Diamond vs single segment 2/3

Double segments are more commonly used as there is less preasure on each diamond segment resulting in lower cost and longer tool life. In principle double segments are used on softer concrete to prevent unwanted excess removal of the concrete stock.

Diamond vs single segment 3/3

A single segment is more commonly used on very hard surfaces as this increases the grinding pressure per diamond segment. This will result in a higher productivity and more aggressive concrete stock removal.

A significantly shorter tool life can be expected when using single segments due to the increase in segment preasure.

Husqvarna PG 680

Eelised

Kasutusvaldkond

Suure võimsusega masin

Vastupidav masin

Palju erinevaid kasutusvõimalusi

Täielikult läbiproovitud

Soodsa hinnaga

5-kordse tihendusega mehhanism

Lihtsalt kasutatav juhtkarp.

Redi-Lock™

Hiperfloor™

Ergonoomilised eelised

Dual Drive Technology™

Parim oma klassis

Täiskummirattad.

Videos

Tehnilised andmed: PG 680

Soovitatavad tööriistad

Mudel

Lisatarvikud: PG 680

Safety instructions

Safety instructions

Unpacking

Unpacking

Setup workspace

Setup workspace

Assembling diamonds

Assembling diamonds 1/3

Assembling diamonds 2/3

Assembling diamonds 3/3

Adjusting Handlebar

Adjusting handlebar

Connect DC

Connect DC

Powering up machine

Powering up machine

Smooth start

Smooth start

Setting speed and rotation

Setting Speed and rotation 1/2

Setting Speed and rotation 2/2

Dual drive Technology

Dual Drive Technology™

Counter rotation

Counter rotation 1/2

Counter rotation 2/2

Same direction rotation

Same direction rotation 1/2

Same direction rotation 2/2

Grind-pattern relevancy

Relevance of grindning patterns

Grinding close to a wall

Grinding close to a wall

Diamond selection

Diamond selection

Application reference

Full set vs Half set

Full set vs Half set 1/3

Full set vs Half set 2/3

Full set vs Half set 3/3

Diamond vs single segment

Diamond vs single segment 1/3

Diamond vs single segment 2/3

Diamond vs single segment 3/3

Dokumentatsioon: PG 680