Husqvarna PG 530

Husqvarna PG 530 on ühefaasiline planetaarlihvija, millel on erakordne võimsus, sobib suurepäraselt kodus kasutamiseks ja väiksemateks kommertstöödeks. Loodud spetsiaalselt 220-240 V pingevahemikule (saadaval ka 3-faasiline versioon) Mudel 530 on valmistatud uusima tehnoloogia järgi ja on oma klassis suurema võimsuse ja sooritusvõimega kui ükski teine kolmepeaga planetaarlihvija.

Eelised ja rakendused
Tehnilised andmed
Soovitatavad tööriistad
Lisatarvikud, osad ja kaasnevad tooted
Kasutusjuhend
Dokumentatsioon

Eelised

Kasutusvaldkond

Kasutusvaldkond
Saab kasutada alates betoonpõrandate ettevalmistamisest ja parandamisest kuni betoonpõrandate lihvimise ja poleerimiseni ning terazzo ja muu looduskivi parandamise ja poleerimiseni.
Suure võimsusega masin

Suure võimsusega masin
Suure võimsusega ja tootlikkusega masin suurendab kasumit ja aitab säästa aega.
Vastupidav masin

Vastupidav masin
Suurepärane tööstuslikuks kasutamiseks mõeldud konstruktsioon tagab atraktiivse kuid vastupidava masina.
Palju erinevaid kasutusvõimalusi

Palju erinevaid kasutusvõimalusi
Võimaldab mitmeid erinevaid rakendusi. Väga mitmekülgne varustus.
Täielikult läbiproovitud

Täielikult läbiproovitud
Igakülgselt läbi proovitud praktilises töös, mis tagab tehnoloogilise efektiivsuse enamus rakenduste j olukordade puhul.
Soodsa hinnaga

Soodsa hinnaga
Kulutused tööriistadele ja hooldusele ruutmeetri/ruutjala kohta on väikesed.
5-kordse tihendusega mehhanism

5-kordse tihendusega mehhanism
Ainulaadne 5-kordne sulgemismehhanism kaitseb laagreid ja sisedetaile betoonitolmu ja püdeliku eest ning pikendab seega masina kasutusiga enne esimest hooldust ja järgmiste hoolduste vahel.
Redi-Lock™

Redi-Lock™
Husqvarna Redi Lock™ on kiire ja lihtne teemanttööriistade vahetamise süsteem. Tugev konstruktsioon tagab maksimaalse kaitse ja tööea.
Pinnatöötlemine ja betooni poleerimine

Pinnatöötlemine ja betooni poleerimine
PG 530, PG 680 ja PG 820 on suurepärased masinad kõikvõimalikeks suuremahulisteks poleerimis- ja lihvimistöödeks. Sobivad suurepäraselt nii märg- kui ka kuivlihvimiseks. Nende kolme peaga lihvijad avaldavad suuremat allapoole suunatud survet ja edastavad rohkem võimsust, mis võimaldab ebaühtlastel pindadel väga stabiilselt töötada.

Kolme peaga lihvijal on uudsed omadused ja kasutusvaldkonnad. Dual Drive Technology(tm). Väga võimas ja eemaldab kiiresti kõvu vastupidavaid pinnakatteid ning seda või kasutada põrandate poleerimiseks kodus ja kommertstingimustes. Edasi/tagurpidi suunas võimalik töötada erineva kiirusega. Lihtne manööverdada ja parem juhitavus. Hea manööverdamisvõimega ja paremini juhitav. Kaal vaid 200 kg. Väikesed kulud varustusele. Siledam ja ühtlasem lihvimispind kui 4-pealise masinaga lihvides. Tolmuvaba, kui kasutada koos 3300 tolmukogujaga. Võib kasutada nii märg- kui kuivlihvimiseks.

Ergonoomilised eelised

Raami ja käepideme disaini tõttu väike mõju kehale.
Parim oma klassis

Kategooria parim toode nii tootlikkuse, usaldusväärsuse osas ja tootel on teistega võrreldes pikem tööiga esimese ja järgmiste hooldus vahel.
Täiskummirattad.

Täiskummirattad aitavad tagada sujuvama lõikamise ja lihvimise.
Lihtsalt kasutatav juhtkarp.

Juhtkarp on selgelt märgistatud ja hõlpsalt kasutatav. Reguleerib ja juhib masina erinevaid funktsioone.

Tehnilised andmed: PG 530

Mootor
Võimsus	3,73 kW
Voolutugevus	16 A
Pinge	220 / 480 V
Voltage	380 - 480 V
Faasid	3

Spetsifikatsioonid
Lihvimislaius	530 mm

Mõõdud
Kaal	215,46 kg

Soovitatavad tööriistad

Mudel	G 11X1	Redi Lock G 1150	Redi Lock G 1120	Redi Lock G 1170	Redi Lock G 1140	Redi Lock G 1110
Optimaalne Hea Vastuvõetav —
Materjalid

Safety instructions

Safety instructions

Under no circumstances may the machine be started without having read the operators manual and paid special intensions to the safety instructions found in the operator’s manual. Should the user fail to comply with these, Husqvarna Construction Products Sweden AB or its representatives are free from all liability both directly and indirectly. Read through these operating instructions and make sure that you understand the contents before starting to use the machine. Should you, after reading these safety instructions, still feel uncertain about the safety risks involved you must not use the machine. Please contact your dealer for more information.
Unpacking

Unpacking

To prevent damage to the Grindng shrould when unpacking and transporting ensure to follow the recommended procedure as outline in the supporting video.
Setup workspace

Setup workspace

Position grinder on the working area. Set handle in upright position (illustrated right).

Pull back on handle using the kicker bar to lift grinding head off the ground.

Lay machine back on the ground.

WARNING!

Ensure STOP/RUN switch is in STOP position as unintentional starting of machine while changing discs can result in serious injury.
Assembling diamonds

Assembling diamonds 1/3

Have a set of gloves ready, as diamonds can get very hot during dry grinding applications.

WARNING!

Ensure STOP/RUN switch is in STOP position as unintentional starting of machine while changing discs can result in serious injury.

Assembling diamonds 2/3

As different applications require different selections of diamond tools, there will be many occasions when the grinding discs need to be changed.

Place diamonds as shown in the Redi Lock™ diamond holder disc and secure by tapping lightly. Assembly discs on planetary head lock screws by slightly rotating it.

Note

When using the machine, each grinding head should always have the same diamond type and number of diamonds as the other grinding heads. Each grinding head must have diamonds the same height as the other grinding heads.

WARNING!

Ensure STOP/RUN switch is in STOP position as unintentional starting of machine while changing discs can result in serious injury.

Assembling diamonds 3/3

Adjust rubber skirt so that a good seal is established between the floor and head of the machine. Ensure join in skirt is at the front of the machine to allow for better air flow. Setting of the skirt is essential to obtain good dust extraction and minimise the possibility of airborne dust.

WARNING!

Ensure STOP/RUN switch is in STOP position as unintentional starting of machine while changing discs can result in serious injury.
Adjusting Handlebar

Adjusting handlebar

Set handle to most comfortable working height using adjustment lever.

Note

It is recommended that this height be set as close as possible to the height of the operator’s hip bone. When the machine is running, there can be a slight grinding force/pull to one side that can be felt through the handlebars. Use the hip to resist this force instead of trying to control this through the arms (such positioning will be much easier for the operator using the machine over prolonged periods of time).
Connect DC

Connect DC

-Connect the hose to the PG Grinder.

-Connect the hose to the DC.

-Attach the plastic bag to the DC, if this is not already in place.

-Plug in the power cable to the DC.

Note

The power cable dipictad in the footage may vary from region to region.
Powering up machine

Powering up machine

Ensure the STOP/RUN switch is set on Stop (rotate counter clockwise).

Plug power supply to machine. Only turn power on at plug once fully connected.

Disengage Emergency Stop button (twist clockwise).

Depress Power button. On doing so, a soft “clunk” should be heard to come from within the electrical cabinet. This indicates the line contactors have engaged, supplying power to the drives/frequency converters.

Note

The power cable dipictad in the footage may vary from region to region.

Note

Always have the DC Vac running before starting to run the Grinder
Smooth start

Smooth start

Standing behind machine with handlebars set as described earlier, apply a small amount of downward pressure on the handle. Switch the machine to run mode using the STOP/RUN switch on the control panel.

The machine should start smoothly and accelerate to the selected speed over a period of 5 seconds.
Setting speed and rotation

Setting Speed and rotation

On the control panel there is a FORWARD / REVERSE and Speed dial knob. Generally, when starting the machine for the first time on any given application, it is advised the speed setting should not exceed 7, initially. When the operator is comfortable with the application, speed may be increased.

The machine should start smoothly and accelerate to the selected speed over a period of 5 seconds.
Same direction rotation

Same direction rotation 1/2

While in same direction rotation, the diamonds closer to the centre of the machine move in the opposite direction to the planetry rotation.

The diamonds toward the outside move in the direction of planetary rotation.

As the outer diamonds are being accelerated in the direction of planatery rotation they grind more aggressively creating an outer band where the machine cuts more effectively.

Same direction rotation 2/2

When the machine is moved forward, the middle zone is still ground more thoroughtly then the outer zones but not as much as in the case of counter rotation. The end result is a more even cut through the middle zone when compared to the outer zones, which is less prominate then in counter rotation.
Grind-pattern relevancy

Relevance of grind-patterns

All planetary grinders remove more stock from the middle of the grinder. Always overlap the outer zones to ensure efficient and clean grinding.

Remember to change the grinding rotation each pass to maintain a uniformed direction over the floor.
Grinding close to a wall

Grinding close to a wall

When the machine is in operation it will slightly pull to one side. This force is determined by the planetary head rotation. When the head of the machine pulls in to the wall the operator will get a much closer cut to the wall.

A comfortable operating position should allow the handle bar to rest firmly against the operator´s hip.
Diamond selection

Diamond selection

The way diamond segments are set-up on the grinding heads of the machine will also greatly influence the performance of the machine, the productivity levels and also the finished floor quality.
Application reference
Full set vs Half set

Full set vs Half set 1/3

There are basically two types of diamond configurations that can be used when using the Husqvarna PG grinders:

Full set of diamonds. When there are diamonds placed at all positions on the diamond holder discs.

Half set of diamonds. When there are diamonds placed at each alternating positions on the diamond holder discs.

By changing the way the diamonds are set-up on the diamond holder discs, an operator can significantly affect the performance of the machine and therefore the finished product.

Full set vs Half set 2/3

A full set of diamonds will cut a flater floor when compared to a half set of diamonds.

The full set will remove all the high spots instead of carring with the surface of the floor and droping down into the low or softer spots.

With a full set of diamonds the highest level of flatness will be achivied.

Full set vs Half set 3/3

A half set of diamonds will follow the surface of the floor.

The grinder can be placed on an uneven surface and yet still find a stable footing. The half-set diamond configuration should be used when a flat floor is not required.

The half set will carry over the high spots and into the low spots, which is ideal to remove floor coatings or glues where optimum flatness is not the overall objective.
Diamond vs single segment

Diamond vs single segment 1/3

As well as using full set and half set, the operator can also choose from double or single segment tools. This will enable the operator to have control over both his tool economy and productivity.

Double segments: A double segment tool consists of two diamond segments on one Redi Lock™ shoe.

Single segments: A single segment tool consists of one diamond segments on one Redi Lock™ shoe.

Diamond vs single segment 2/3

Double segments are more commonly used as there is less preasure on each diamond segment resulting in lower cost and longer tool life. In principle double segments are used on softer concrete to prevent unwanted excess removal of the concrete stock.

Diamond vs single segment 3/3

A single segment is more commonly used on very hard surfaces as this increases the grinding pressure per diamond segment. This will result in a higher productivity and more aggressive concrete stock removal.

A significantly shorter tool life can be expected when using single segments due to the increase in segment preasure.

Husqvarna PG 530

Eelised

Kasutusvaldkond

Suure võimsusega masin

Vastupidav masin

Palju erinevaid kasutusvõimalusi

Täielikult läbiproovitud

Soodsa hinnaga

5-kordse tihendusega mehhanism

Redi-Lock™

Pinnatöötlemine ja betooni poleerimine

Ergonoomilised eelised

Parim oma klassis

Täiskummirattad.

Lihtsalt kasutatav juhtkarp.

Tehnilised andmed: PG 530

Soovitatavad tööriistad

Mudel

Lisatarvikud: PG 530

Silikoonrõngas

Safety instructions

Safety instructions

Unpacking

Unpacking

Setup workspace

Setup workspace

Assembling diamonds

Assembling diamonds 1/3

Assembling diamonds 2/3

Assembling diamonds 3/3

Adjusting Handlebar

Adjusting handlebar

Connect DC

Connect DC

Powering up machine

Powering up machine

Smooth start

Smooth start

Setting speed and rotation

Setting Speed and rotation

Same direction rotation

Same direction rotation 1/2

Same direction rotation 2/2

Grind-pattern relevancy

Relevance of grind-patterns

Grinding close to a wall

Grinding close to a wall

Diamond selection

Diamond selection

Application reference

Full set vs Half set

Full set vs Half set 1/3

Full set vs Half set 2/3

Full set vs Half set 3/3

Diamond vs single segment

Diamond vs single segment 1/3

Diamond vs single segment 2/3

Diamond vs single segment 3/3

Dokumentatsioon: PG 530