Husqvarna DS 50 AT

Statiiv, mida saab keerata ja nurga alla seada, millel on alusplaat reguleeritava poldi jaoks. Statiiv on varustatud kahe ajamiga kelguga.

Eelised ja rakendused
Tehnilised andmed
Lisatarvikud, osad ja kaasnevad tooted
Kasutusjuhend
Dokumentatsioon

Eelised

Statiivi kallutatavus ja pööratavus muudab seadme väga mitmekülgseks ning võimaldab kasutajal puurida erinevates asendites. Kahe ajamiga kelk võimaldab valida tööle vastava puurimiskiiruse. Tänu kiirühendusele saab kasutaja mootorit kiiresti ja lihtsalt paigaldada ja eemaldada.

Uuesti arendatud kelk

Puurmasinastatiividel on uue arendusega kelk, millel on üks või kaks hammasülekannet ja kiirühendus puurmasinate lihtsaks ühendamiseks. Kõik statiivid on saadaval koos transpordiratastega.
Transpordirattad

Statiivil on transportrattad.

Rakendused

Kaldpuurimine.

Kaldpuurimine.
Aukude puurimine sujuvalt reguleeritud nurkade all.
Pistepuurimine

Pistepuurimine
Mitmete aukude üksteise kõrvale puurimine, et teha suuremaid avasid.

Tehnilised andmed: DS 50 AT

Lõikamisvarustus
Maks. puuritera läbimõõt	300 mm
Tee pikkus	609,6/0 mm

Sammas
Kalle	Pidev
Kallutamine	+/-90º

Muud spetsifikatsioonid
Sobib	DM 280

Mõõdud
Kaal (ilma lõikevarustuseta)	63,45 kg
Pakend, mõõdud, PxLxK	1981,2x914,4x609,6 mm
Kaal koos pakendiga	69,75 kg

Sidustooted: DS 50 AT

DM 340

Kergesti käsitsetav Husqvarna puurmasin. DM 340 on varustatu...
DM 280

Seda uut Husqvarna puurmootorit on äärmiselt lihtne kasutada...
AD 10

AD 10 on ainulaadne automaatpuurimise süsteem, mis kuulub er...

Lisatarvikud: DS 50 AT

Tööriistakast

Tööriistakast
Tagumine tugi

Tagumine tugi
Väikese läbimõõduga vaakumplaat

Väikese läbimõõduga vaakumplaat.
VP 200

Vaakumpump, võimas elektrimootor ja torudest raam. Varustuse...
CD 40

Husqvarna Core Down-süsteem CD 40 on praktiline, turvaline j...
Ankurduskomplekt

Standardne ankurduskomplekt suure painduva mutri, hoidekruvi...
Ankrud

Ankurduskomplekt, koos suure mutri, kinnituskruvi ja 5 ankru...
Ankrusüsteem

Ankrusüsteemid abrasiivsete materjalide külge ankurdamiseks.
Ankrusüsteem

Ankrusüsteemid abrasiivsete materjalide külge ankurdamiseks.
Varustus nurga all puurimiseks

Tõkkerõngas
Auto statiiv

Statiiv, mida saab kinnitada sellele auto rattaga peale sõit...
Vahelüli kiirühenduse jaoks

Vahelüli, 50 mm, kiirühendamiseks suurte puuriteradega puuri...
Veekoguja

Suur valik veekogujaid.
Veekoguja

Suur valik veekogujaid.
Veekoguja

Suur valik veekogujaid.
Veekoguja

Suur valik veekogujaid.
Veekoguja

Suur valik veekogujaid.
Veekoguja

Suur valik veekogujaid.
Veekoguja

Pakume laias valikus veekogujaid. Erinevate läbimõõtudega te...
Veekoguja

Pakume laias valikus veekogujaid. Erinevate läbimõõtudega te...
Veekoguja

Pakume laias valikus veekogujaid. Erinevate läbimõõtudega te...
Veekoguja, V-kujuline

Veekoguja, V-kujuline
Veekoguja, V-kujuline

Veekoguja, V-kujuline
Veekoguja

Pakume laias valikus veekogujaid. Erinevate läbimõõtudega te...

Safety instructions

Safety instructions

Under no circumstances may the machine be started without having read the operators manual and paid special intensions to the safety instructions found in the operators manual. Should the user fail to comply with these, Husqvarna Construction Products Sweden AB or its representatives are free from all liability both directly and indirectly. Read through these operating instructions and make sure that you understand the contents before starting to use the machine. Should you, after reading these safety instructions, still feel uncertain about the safety risks involved you must not use the machine. Please contact your dealer for more information.
Floor mounting

Floor mounting

Drill a 15 mm hole for the M12 expander bolt.

Put the drill stand over the expander bolt and tighten the drill stand with a M12 bolt.

Adjust the level screws to reach stability and straightness for the drill stand.
Drill motor attachment

Drill motor attachments

The feed housing on the drill stand consists of a quick-action attachment for drill motors.

Fit the drilling machine in the quick-action attachment.

Use the feeding handle to lock and secure the drill motor.
Pivot the column

Pivot the column

Loosen the bolt on the lower right side of the column.

Loosen the quick connector bolt on the lower back side of the column. (This has four 90 degrees positions to lock in).

Rotate the column (360 degrees) to match the correct position.

Lock the two bolts to secure the column.
Tilt the column

Tilt the column

Loosen the two bolts on the base plate.

Adjust the column to match the correct angle. (0 – 180 degrees)

Lock the two bolts to secure the column.
Fit the drill bit

Fit the drill bit

Fit the drill bit on the spindle axis on the motor anti-clockwise (seen from the motor)
Water and electricity

Water and electricity

Connect water and electric power. Make sure the PRCD is reset.
Drilling

Drilling

Switch on the drill motor

Unlock the locking handle placed on the left side of the feed housing.

Feed the drill motor with the handle WARNING Before drilling, check that all locking screws are tightened well. Serious accidents can occur if the concrete core remains in the drill when backing out the drill motor/drill bit from the floor, wall or ceiling. A maximum of one extension module may be used.
Cleaning

Cleaning

It is very important that the drill rig is kept clean and tidy in order to maintain its function. The rig is suitably cleaned using a high pressure washer and then wiped dry.
Lubrication

Lubrication

After washing it is important that the rig’s moving parts are lubricated using standard grease to counteract corrosion on the contact surfaces.
Description

Description

When drilling in an angle, the column is tilted to fit the correct angle (0-180 degrees). The down side of drilling in angle is that the column loses travel length and an extension must often be added to the drill bit. By using the DS 50/70 which can be pivoted as the same time as tilted the travel length is gained back.
Operation

Operation

In this application the DS 70 is used (same functions as on the DS 50). The drilling is performed with both an angled and a tilted column.
Description

Pivoted drilling

When drilling in confined spaces or a series of holes the pivot function is usable. By simply pivot the column (360 degrees) to a given hole, a lot of time is saved instead of having to re-place the drill stand for each hole.
Operation

Operation

By loosing the pivot screws the column can be pivoted to the given position. A safe and time saving step to prevent reattaching the drill stand for a new position or location.
Description

Description

The Husqvarna Core Down System, CD 40, is a practical, safe and easy to use drill core collector for the safe collection and removal of concrete drill cores.
Operation

Operation

Place the CD 40 in line with the drilled hole.

Clamp the system to the ceiling by loosen the handle and lift it against the ceiling and fasten it. <rbNot></rbNot> Lift the wall collector, place it by the drill bit/core and secure.

Lift the drill bit/core and place it in the collector.

Grab the handle and slowly lower the collector until safe height is reached.

Remove the drill bit/core.
Description

Description

The unique range of water collection system includes vacuum-hold collectors of different design for different use.

The V-shaped collector for stitch drilling

The circular collector for normal drilling

The half-circular collector for drilling close to the wall/floor.
Operation

Operation

Simply hold the water collector to the wall and connect the wet vacuum cleaner to it. The vacuum will hold the collector and will also take care of almost all water coming from the drill bit.

Husqvarna DS 50 AT

Eelised

Uuesti arendatud kelk

Transpordirattad

Rakendused

Kaldpuurimine.

Pistepuurimine

Tehnilised andmed: DS 50 AT

Sidustooted: DS 50 AT

Lisatarvikud: DS 50 AT

Väikese läbimõõduga vaakumplaat

Safety instructions

Safety instructions

Floor mounting

Floor mounting

Drill motor attachment

Drill motor attachments

Pivot the column

Pivot the column

Tilt the column

Tilt the column

Fit the drill bit

Fit the drill bit

Water and electricity

Water and electricity

Drilling

Drilling

Cleaning

Cleaning

Lubrication

Lubrication

Description

Description

Operation

Operation

Description

Pivoted drilling

Operation

Operation

Description

Description

Operation

Operation

Description

Description

Operation

Operation

Dokumentatsioon: DS 50 AT